· Starter course: First course of shingles installed along the drip edge at the eaves below the first exposed course of shingles. Starter-course shingles are often a regular shingle with the exposed portion removed. Underlayment: Asphalt-impregnated felt paper or peel-and-stick membrane applied over the sheathing before the shingles go on.
First, determine how much the starter course will overhang the drip-edge: 1⁄4 in. to 3⁄4 in. overhang is typical, but some roofers allow as much as 1 in. if eave or rake boards are bowed. Along the eave, extend your tape measure past the drip-edge the amount of the overhang. If that overhang is 1 in., make crayon marks on the underlayment ...
Starter shingles are the initial shingle products installed on the roof, just before the first course of the finish shingles, which will comprise the visible parts of the roof. Since the starter shingles will be covered by the roof shingles, it doesn’t matter what …
· A starter strip is an asphalt based shingle utilized to waterproof the eave and rake edges of your home during a re-roof. Take a look at your roof and you’ll see how the field roofing shingles are overlapped to create seamless flow of water without penetration. But along the eave line, roofing shingles come to an edge and can’t be overlapped.
A starter strip is an asphalt based shingle utilized to waterproof the eave and rake edges of your home during a re-roof. Take a look at your roof and you'll see how the field roofing shingles are overlapped to create seamless flow of water without penetration.
The starter course protects your roof by filling in the spaces under the edges of the first row of exposed shingles. In other words, the starter course is a backing for the first visible row of shingles.
PABCO® Universal Starter is applied on the leading edge under the first course of asphalt shingles and features a sealant stripe that helps provide wind resistance for your roof system.
2:306:00How to Install Starter Shingles - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what you're gonna want to do is you're going to want to come off of that about a quarter of anMoreSo what you're gonna want to do is you're going to want to come off of that about a quarter of an inch and that will give you your perfect spacing on here and then you're gonna go ahead and nail that.
You do need to use a starter course with architectural shingles. The starter edge will help seal the edges and cover your shingle joints. As it won't be visible on the finished roof, you don't need to worry about the look of your starter strip and whether it matches your architectural shingles.
1:253:53How to Install Starter Strip Roofing Shingles | Mastering the Roof by GAFYouTubeStart of suggested clipEnd of suggested clipEvery starter strip requires a minimum of 4 nails driven in a straight line fashion. One and a halfMoreEvery starter strip requires a minimum of 4 nails driven in a straight line fashion. One and a half to three inches above the shingles bottom edge.
Universal Starter: An upgraded starter shingle that provides a foundation for PABCO Roofing's shingle products.
Drip edge is metal flashing installed at the edges of the roof to keep water away from your fascia and from getting underneath your roofing components. If your roof doesn't have drip edge, water gets behind your gutters and rots out both your fascia board and roof decking.
Simply put, a roof rake edge is installed to cover the top edge of the siding where it meets the roof. You can think of it as a type of awning that is designed to allow water to flow off the roof and down onto the ground below, instead of down the side of your home.
0:435:55How To Properly Start Shingle Courses On A Roof - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd up your Gables. First thing you're gonna want to do is take a full shingle. And you're gonna goMoreAnd up your Gables. First thing you're gonna want to do is take a full shingle. And you're gonna go flush. Along the eave starter. And flush along the rake starter.
The starter strip is the layer of shingles underneath the first course along the edge of the roof. Some roofers simply take regular shingles, flip them upside down and nail them down as a starter course.
After installing drip-edge along the eaves, double the first course of shingles or, as shown, install a starter strip. The lower edge of the starter strip overhangs the drip-edge by 1⁄4 in. to 3⁄4 in. —or even 1 in. if bowing eaves or rake boards require it.
When roofers install those shingles at the eave on the first course, the starter is visible, and, therefore, its color is relevant. In this case, an additional starter shingle course, in matching colors to the finished shingle, is required as a secondary starter layer.
Starter shingles are the initial shingle products installed on the roof, just before the first course of the finish shingles, which will comprise the visible parts of the roof. Since the starter shingles will be covered by the roof shingles, it doesn’t matter what color they are, (except in special situations — see below).
Starter strips are an important and integral part of an asphalt shingle roof system. They aid the roof’s water-shedding function by covering shingle joints (and cutouts in traditional three-tab shingles) at the eaves.
A simpler and very useful purpose for using starter shingles along the rake edge is that it gives the installer a nice straight line to use as a guide when ending each course of the field shingles.
Whether installed at the eave or the rake, the starter shingles should overhang the edge of the roof by ¼ inch to ¾ inch. Typically, the finish shingles are then installed to align with the edge of the starters.
IKO’s starter shingle product, Leading Edge Plus, offers the latest evolution in roof starter strips. Professional contractors who make the smart decision to use them will find they save time, are easy to install and are consistently sized. Each Leading Edge Plus starter strip “shingle” is perforated right down the middle so that you get two starter strips out of each roof shingle.
As well, starter shingles have a sealant strip, and, when positioned correctly, the sealant strip will be on the top surface and at the lowest edge of the roof . At the roof’s rake edges, the starter doesn’t necessarily perform that joint-covering function it performs at the eave, but it is integral in the roof’s overall wind resistance.
Starter shingles (also known as starter strips) are a key component to your new roofing system. A starter strip is an asphalt based shingle utilized to waterproof the eave and rake edges of your home during a re-roof. Take a look at your roof and you’ll see how the field roofing shingles are overlapped to create seamless flow ...
Factory starter is also a part of the GAF complete roofing system and required to qualify the roof for an upgraded warranty. Here are a few technical points for Pro-Start starter strips (from GAF website):
The edge of the starter strip should hang over the eave and rake edge 3/4″ in order to create a drip edge. This is required on all Golden Pledge system warranties.
Without starter strips or starter shingles, water will likely penetrate your roof edge. A good underlayment, like GAF Tiger Paw synthetic hybrid underlayment goes a long way to reducing damage. But it is only a secondary layer of protection that functions robustly when the water that reaches it is a low enough quantity.
Universal Starter Prev Next PABCO ® Universal Starter is applied on the leading edge under the first course of asphalt shingles and features a sealant stripe the helps provide wind resistance for your roof system.
In addition, the continuous sealant ensures an effective seal between the starter and the first course of shingles. Starter strip shingles are packaged 2-pieces per shingle, 16 shingles per bundle, 100 lin. ft. Perforation down the center allows for easy separation, saving installation time and money.
TAMKO® 10-INCH STARTER TAMKO® 10 INCH STARTER universal starter course shingles are factory cut starter strips made of fiberglass mat coated on both sides with coating grade asphalt and surfaced with ceramic granules to help protect from ultraviolet degradation. • Pre-cut to reduce the labor and need of field cutting other materials.
TAMKO® 10 INCH STARTER Universal Starter Course Shingles are factory cut starter strips made of tough fiberglass mat coated on both sides with coating grade asphalt and surfaced with ceramic granules for protection from ultraviolet degradation.
CertainTeed's Universal Starter Strip Shingles (7" x 36") combines durability and flexibility for better resistance to blow-off. Availability depends on sales region. Limitations: Use as a starter course on shingle roofs with slopes greater than 2" per foot and can be used with any 12" x 36" shingle having a weather exposure of < 5".
Starter Shingle - is the shingle at the 'bottom edge' of the roof with the exposure portion trimmed off, leaving just the self-seal strip and top lap. They are fastened along the eaves edges to seal down the first course of shingles and provide coverage material beneath the tab cutouts just like the top lap of each successive course.
Starter shingles are the initial shingle products installed on the roof, just before the first course of the finish shingles, which will comprise the visible parts of the roof. Since the starter shingles will be covered by the roof shingles, it doesn't matter what color they are, (except in special situations — see below).
High-Performance Starter are starter course shingles designed specifically for use with GrandManor® and High land Slate® shingles - and are the only approved installation alternative to using the shingles themselves .
CertaSeal is a high-grade adhesive made from a proprietary blend of asphalts and polymers that seals shingles together on the roof to safeguard against wind uplift, shingle blow off, and moisture infiltration. Unlike harder sealants that can dry out and crack over time, it is designed to remain pliable and accommodate the slight structural shifts caused by years of temperature and weather changes. Learn more.
This will help determine how the shingles will lay on the roof width. Most asphalt shingles are 3 feet (91.4 centimeters) in length. If your roof's width is not an even multiple of the shingle's length, you will have a partial piece on one end of each row. The bottom row of shingles must hang past the edge of the roof.
Depending on the type of shingles you're using and the roof you're working on, you may need to marking a chalk guideline beginning 7 inches (17.8cm) from the bottom roof edge. In either case the glue strip of the starter course is then placed along the drip edge, and at the rake edges as well.
On steep roofs, toe-steps should be nailed to the roof with metal strips holding the toe-steps, to keep you and supplies in place -- as well as using safety rop es and a harness.
The winter months are not good for installing shingles. A good time is late spring/early summer.
The starter is very necessary to keep water out.
I think starters along the rake also reduce the amount of drip off the rake and onto the siding.I some times see it on older houses in NW Ohio, nevr on new stuff
You might politely mention to your neighbor that he look at the instructions printed on the wrapper of the shingles. There is no shingle system in the world that does not use some form of starter.
Based on everything I’ve read (I know – a little knowledge is a dangerous thing), it’s standard practice to install a row of “starter” shingles under the the first row of shingles on all eaves. Some even recommend on all rakes. What is the purpose? I suppose the double thickness on the eaves will make the first row “lay right” and match the other shingles. In the Taunton “Roofing with Asphalt Shingles” book the auhor also indicates that the starter strip helps with water resistance.