how to start the first course of shingles

Symptoms

Causes

Prevention

Complications

How do you start a starter for shingles?

2:156:00How to Install Starter Shingles - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what you're gonna want to do is you're going to want to come off of that about a quarter of anMoreSo what you're gonna want to do is you're going to want to come off of that about a quarter of an inch and that will give you your perfect spacing on here and then you're gonna go ahead and nail that.

How do I get my first row of shingles straight?

Lay the first row of shingles directly covering the narrow starter row. Snap a horizontal chalk line over the starting row to use as a guide. Cut six inches off the length of the first starter shingle nailed on, then use the rest of them full size.

How do you start the first row of three tab shingles?

0:244:56How to : Roofing - Where to start laying (three) 3 tab shingles / starter ...YouTubeStart of suggested clipEnd of suggested clipSo after this one here is nailed in place then you say how I line it up. So we've cut a half tab offMoreSo after this one here is nailed in place then you say how I line it up. So we've cut a half tab off boat. So we want it flipped upside down lined up on a thirty inch mark.

What should I put down before shingles?

Before laying down shingles, you need to protect the roof with sheathing. Roll out a single layer of roofing felt or tar paper, which serves as a moisture barrier. Begin this layer at the bottom of the roof and add it in horizontal rows, with a slight overlap to prevent leaks.

Do you need a starter strip for shingles?

The starter strip is crucial because it adheres to the shingles on the edges of your roof and protects them from the elements. Without starter strip shingles, a gust of wind would have no trouble sneaking under the shingles on the edges of your roof and blowing them up, and perhaps even off, your roof.

How far should shingles overhang?

Shingles should not extend more than 3/4” (19 mm) past the drip edge. If shingles overhang the edge of the roof by more than 3/4” (19 mm), then they are not supported and may crack and break off. In addition, the wind resistance at the roof edge may be compromised.

Do you nail shingles on the tar line?

0:153:52How to : Roofing - Where and How to Nail a Shingle - YouTubeYouTubeStart of suggested clipEnd of suggested clipBreak put a nail right on the tar line. Okay on the on the next one right here above the littleMoreBreak put a nail right on the tar line. Okay on the on the next one right here above the little break and on the tar lines okay. And then on each end of the shingle.

How do you start shingles straight on a non square roof?

Roll out 3 feet of the roof starter roll at one corner of the lower edge of the roof. Align the lower edge and end with the corresponding lower edge and end of the roof. Fasten the upper corner of the starter in place, using a shingle hatchet or hammer and a 1-inch roofing nail.

How do you shingle a roof step by step?

Here are the basic steps to shingle a roof.Step one in any roofing project is always safety first. ... Understand the physics of how a sloped shingle roof works. ... Deck preparation. ... Work from the bottom up. ... Ice dam protection at the eaves. ... Underlayment for overall secondary roof protection. ... Covering the joints and valleys.More items...

Do you need black paper under shingles?

Answer: Roofing felt is a layer of tar paper installed beneath the shingles to provide a backup waterproof membrane in case of leakage. Felt, otherwise known as underpayment, is required when asphalt shingles are installed as a first layer of roofing or when they are applied over wood shingles or a built-up roof.

What is the purpose of the black paper under shingles?

Felt roofing paper offers a layer of protection during this period before the shingles are secured. You don't want to risk wood rot, moisture, or mold on a new roof before shingles are secured. This extra layer helps shingles lay flat by providing an even surface for the shingles to lay flat.

What is the black paper under shingles?

What is roofing felt paper? Sometimes called roofing felt underlayment, roofing tar paper, or roll roofing, this is a layer of protection installed between the roof deck and the roofing shingles.