Full Answer
Jun 14, 2019 · HardiePlank lap siding requires a starter strip beneath the first course. You have two options here – you can make your own or you may be able to find acceptable prefabricated, third-party starter strips available for purchase. You can make your own fiber cement starter strip by ripping a piece of HardiePlank lap siding into 1-1/4-inch strips.
3) Overlap second piece of Hardiplank siding with EZ Line 1-1/4", utilizing EZ Line alignment aid. weather-resistive barrier * 1) Install 1/4” lath strip to ensure consistent plank angle. 2) Begin first course at end of far left wall and nail to stud. 3) Second course begins at …
Nov 29, 2017 · From starter strips to correct gap length its important to know the basics for siding installation. Learn how to install HardiePlank lap siding on your home'...
Jul 05, 2021 · Use hot-dipped galvanized or stainless steel nails. Nails should penetrate through the sheathing and at least 1” into studs. Position nails ¾” to 1” from the edge of the siding. Siding can either be blind nailed at the top or face nailed at the bottom.
1:458:13HardiePlank Lap Siding Install Video - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe first course should start at the lowest point of the house. Special. Attention should be made toMoreThe first course should start at the lowest point of the house. Special. Attention should be made to ensure that it's straight and level.
3:1217:4090234 views - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd these starter strips are going to be the first thing you install along the very bottom of yourMoreAnd these starter strips are going to be the first thing you install along the very bottom of your sheathing. And that's going to be what helps to kick out that first row of lap siding.
HardiePlank lap siding requires a starter strip beneath the first course. You have two options here – you can make your own or you may be able to find acceptable prefabricated, third-party starter strips available for purchase.Jun 14, 2019
Sturdi-Starter is a 4-foot long x 1 ¼” wide x 5/16” thick (8 mm) profile extruded polypropylene plastic strip used as a starter strip behind the first course of siding. Sturdi-Starter replaces strips ripped from good planks of siding, saving the installer money and materials, time on the job and extra labor.May 15, 2014
Even though James Hardie does not require a rainscreen in most cases, it can still be a relatively inexpensive way to improve the long-term health and performance of your structure. Particularly with HardiePanel, we always recommend at least a drainable housewrap as a weather barrier.Jul 8, 2020
1¼”Each row of siding should overlap by 1¼” or more.
Fasten the siding – You can fasten it with a pneumatic nailer or nailing by hand. You can use corrosion-resistant screws, or you can use stainless steel or hot-dipped galvanized nails. You can nail the siding by either blind nailing it at the top or face nailing it at the bottom.
James Hardie recommends using stainless steel finish nails when installing HardieTrim products. Use a 2 in. finish nail to fasten trim together. Longer finish nails may bend.
0:214:37Installation-8 HardieTrim® - YouTubeYouTubeStart of suggested clipEnd of suggested clipSpace nails across the width of the board no more than 16 inches on center keep fasteners threeMoreSpace nails across the width of the board no more than 16 inches on center keep fasteners three quarters of an inch back from all edges and three-quarters of an inch from the ends.
Available in commonly-used nominal widths from 101mm (4 in) to 304mm (12 in). HARDIETRIM® BATTEN BOARDS HardieTrim® Batten Boards are a decorative non-load bearing trim product. HardieTrim® Batten Boards are 19mm (¾ in) thick, 64mm (2½ in) wide, and come on 3,658mm (12 ft) lengths.
Plank Widths:5.25″ (4″ exposure)6.25″ (5″ exposure)7.25″ (6″ exposure)8.25″ (7″ exposure)9.25″ (8″ exposure)
James Hardie 5/8" 10-1/4" x 12' Artisan® Shiplap Plank Lap Siding for HardieZone® 10 Primed.