Mar 16, 2013 · TOOLS You Will NEED for Roofing from AmazonBostitch Coil Nailer https://amzn.to/2U1v8E2Shingle Remover https://amzn.to/2FzU5wfRoof Snake https://amzn.to/...
your starter course, hold your rule or tape so that it overhangs the drip edge by 1 in. Make a mark at 12 in. on both ends of the roof deck and strike a connecting line. The top of the starter-course shingles will be laid to this line. Then measure in 10-in, increments up the roof deck, starting from your starter-course line.
Apr 23, 2020 · In today’s video we go over the basic techniques to installing shingle courses on your roof. Please like and subscribe for more instructional videos!!In the ...
0:525:55How To Properly Start Shingle Courses On A Roof - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst thing you're gonna want to do is take a full shingle. And you're gonna go flush. Along theMoreFirst thing you're gonna want to do is take a full shingle. And you're gonna go flush. Along the eave starter. And flush along the rake starter.
1:197:573-Tab Roofing Shingles (Ultimate Guide and Review) - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow you need to make sure it's above 43 degrees is normally what the manufacturer recommendationsMoreNow you need to make sure it's above 43 degrees is normally what the manufacturer recommendations are on installing these so you never ever ever want to install these when it's really cold.
0:0031:35SHINGLES installation STEP by STEP ,MUST watch. - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe starter course which is you can either take our 20 year shingles or have you called a tree typeMoreThe starter course which is you can either take our 20 year shingles or have you called a tree type shingle and just turn it upside down and then you have to nail right here on the edge.
4 inchesShingle Peaks and Hips When you reach a peak or hip, shingle all the way up the first side (until the reveal portion of the shingles is within 4 inches of the peak) and cut the 3-tab shingles just below the ridge. Shingle the other side and allow these pieces to overlap the ridge by no more than 4 inches.Aug 7, 2020
3:326:00How to Install Starter Shingles - YouTubeYouTubeStart of suggested clipEnd of suggested clip10 to 12 inches off of it. And not drop it. And you're gonna start with that. So there's your pieceMore10 to 12 inches off of it. And not drop it. And you're gonna start with that. So there's your piece with your 10 to 12 inches off.
2:453:44How To Cut The Roof Shingles On A Gable Roof - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the reason we cut the shingles. Over they come over 15 mil over from the barge flashing and thisMoreSo the reason we cut the shingles. Over they come over 15 mil over from the barge flashing and this is a termination point where the wood so the barge flashing here hides the edge of the plywood.
2:436:15"Roof Installation: How To Shingle a Valley (HD)" by RoofRepair101YouTubeStart of suggested clipEnd of suggested clipBring the first course of shingles along the eave. And across the valley onto the roof plane thatMoreBring the first course of shingles along the eave. And across the valley onto the roof plane that has the lower slope or a lesser height.
Starter shingles (also known as starter strips) are a key component to your new roofing system. A starter strip is an asphalt based shingle utilized to waterproof the eave and rake edges of your home during a re-roof.May 28, 2013
The GAF shingle application instructions for our entire product line specifically state that that film does not need to be removed. Note: The film strips on the back of each shingle are to prevent sticking together of the shingles while in the bundle. Their removal is NOT required during application.
0:313:52How to : Roofing - Where and How to Nail a Shingle - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere your lines where they were your tabs. Break put a nail right on the tar line. Okay on the onMoreThere your lines where they were your tabs. Break put a nail right on the tar line. Okay on the on the next one right here above the little break and on the tar lines okay.
1:493:21How to Install Laminate Architectural Shingles by Malarkey Roofing ...YouTubeStart of suggested clipEnd of suggested clipRate apply a full-length shingle adjacent to each of the first five courses to extend the patternMoreRate apply a full-length shingle adjacent to each of the first five courses to extend the pattern loosely butting factory edge to factory edge to maintain a straight layout.
Overlap each row at least 3 to 4 inches. If you live in an area with inclement weather, you should consider using a special leak barrier protector. Then, install new flashing (metal flashing is often called "drip edge" along the bottom of the roof near your gutters) and starter shingles at the edges.