how to install beckett water course

Beckett’s CB15 & 20 series pumps have 3 inlet holes on the lid that can be pressed out to best match the installation. Be sure the drain tubing extends past the lid of the pump at least 1” to avoid splashing. Discharge tubing is connected to the 3/8” barb outlet, a hose clamp or zip tie can be used to ensure drip-free operation.

Full Answer

Why install a check valve on a discharge line?

How to connect yellow wires to thermostat?

How to make sure you are hooking up your wires correctly?

What happens if a pump isn't level?

See 1 more

About this website

Help wiring low voltage wires on condensate pump : r/HVAC - reddit

I've searched a lot and can't quite find what I need. I've found that the two extra wires coming out of the condensate pump are the low voltage…

The Proper Way to Install a Condensate Drain Line | eHow

Once you've completed installing a new air conditioner, your work isn't quite finished. Before you switch on the unit, you'll need to know the proper way to install a condensate drain line. These drain lines carry away condensation produced by the operation of the evaporator on the air conditioner unit.

Have a question?

There was a problem completing your request. Please try your search again later.

Top reviews from the United States

There was a problem filtering reviews right now. Please try again later.

Why install a check valve on a discharge line?

It may also be a good idea to install a check valve somewhere on the discharge line to avoid backflow of the discharge water so it can’t be sucked back into the a/c unit. The discharge line should run into a line that goes to the city’s waste, once again to avoid contamination of fresh water.

How to connect yellow wires to thermostat?

Cut the red wire from the furnace to thermostat and connect the yellow wires to the cut ends of the red wire. This way, if the condensate pump fails the safety switch (yellow wires), it will stop the furnace/AC and no more water from condensate will be generated. If heating or AC are a must, then connect the yellow wires to an alarm.

How to make sure you are hooking up your wires correctly?

It is always important to make sure that you turn then power off at the fuse box before installing any electrical components of appliances. Check the local codes to make sure you are hooking up your wires correctly. Hook up the power cord to the specified voltage. Make sure it is connected to a constant power source.

What happens if a pump isn't level?

If the pump isn’t level, it will not function properly. It is also important to make sure that the unit will not spray or splash when it is running. Once the pump is mounted correctly, you are ready to pipe the unit. Use some sort of flexible tubing, if possible, as the drain pipe for the pump.

Why install a check valve on a discharge line?

It may also be a good idea to install a check valve somewhere on the discharge line to avoid backflow of the discharge water so it can’t be sucked back into the a/c unit. The discharge line should run into a line that goes to the city’s waste, once again to avoid contamination of fresh water.

How to connect yellow wires to thermostat?

Cut the red wire from the furnace to thermostat and connect the yellow wires to the cut ends of the red wire. This way, if the condensate pump fails the safety switch (yellow wires), it will stop the furnace/AC and no more water from condensate will be generated. If heating or AC are a must, then connect the yellow wires to an alarm.

How to make sure you are hooking up your wires correctly?

It is always important to make sure that you turn then power off at the fuse box before installing any electrical components of appliances. Check the local codes to make sure you are hooking up your wires correctly. Hook up the power cord to the specified voltage. Make sure it is connected to a constant power source.

What happens if a pump isn't level?

If the pump isn’t level, it will not function properly. It is also important to make sure that the unit will not spray or splash when it is running. Once the pump is mounted correctly, you are ready to pipe the unit. Use some sort of flexible tubing, if possible, as the drain pipe for the pump.