A Soldier Course is created by laying the bricks on end, side by side. The standard practice of this style of brickwork is to be applied to openings in the facade aswell as being used to create a horizontal detail band course around a building.
Full Answer
0:043:00GARDEN WALL HOW TO LAY A SOLDIER COURSE - YouTubeYouTubeStart of suggested clipEnd of suggested clipBoard the most important thing with bricklaying getting that nice enough on there for for freeMoreBoard the most important thing with bricklaying getting that nice enough on there for for free making sure that's not evenly spread on the brick. Just place it on there nice.
5:399:01How to Lay Brick Sills - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd high drown down the middle. Nice and high out there so we don't have any falling back becauseMoreAnd high drown down the middle. Nice and high out there so we don't have any falling back because what you'll find is when you do go to lay that first brick naturally it's going to just want to roll.
So what is the correct angle for a sill? In general, a window sill should have 3-12 or 3″ by 12″ slope or pitch for good rain drainage. 3-12 slope means that for ever 12 inches of horizontal distance (run), the vertical measurement (rise) is 3″. Looking at Table 1.1, this corresponds to 14 degrees of slope.
0:121:52How To Cut A Brick Wall Opening - DIY At Bunnings - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe tools were going to need for doing this an angle grinder with a diamond blade in it I have aMoreThe tools were going to need for doing this an angle grinder with a diamond blade in it I have a drill with a masonry bit of the spirit level mash hammer and a brick bolster.
0:1011:05DIY: Build Your Own Windowsill - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd today we're going to take a look at the process for building a window sill go in this window.MoreAnd today we're going to take a look at the process for building a window sill go in this window. And to do that we're going to be using. Some 2 by 8 cedar.
Sill Adapter A replacement frame component attached to the sill of a finless window being installed into an existing window frame with a sloped sill.
I personally know of no code requirements as to minimum angle of exterior sills, except as common sense dictates....that they should be less than 90 degrees to the window unit/panes and thereby allow any liquid water to run off and away from the unit.
The sill on a rough opening should be sloped so it can direct water that has penetrated the building envelope back to the outdoors. This can be accomplished by cutting the cripple studs at an angle or by adding a sill-wedge or sloped pan after the rough opening has been framed in.
The sill slope of a window is the angle of the sill (angle of the bottom of the window unit). The sills of most Andersen® products are sloped towards the exterior of the home.
0:2917:43Adding windows to a brick wall | Part 1: Opening the wall - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the windows that we're putting in here are actually old windows that came from upstairs I'll fillMoreSo the windows that we're putting in here are actually old windows that came from upstairs I'll fill in with a little clip here in the corner somewhere. So you can see what they look like.
1:484:20How To Install Block Frame Windows in Masonry - YouTubeYouTubeStart of suggested clipEnd of suggested clipCheck the window placement within the wall by measuring from the interior surface of the window orMoreCheck the window placement within the wall by measuring from the interior surface of the window or jamb extension to the interior surface of the wall. The measurement should be consistent.
0:001:06How to Drill a Large Hole in a Brick Wall - Diamond Coated Hole SawYouTubeStart of suggested clipEnd of suggested clipTo cut a large hole in brick use a diamond coated hole saw with a masonry pilot.MoreTo cut a large hole in brick use a diamond coated hole saw with a masonry pilot.