crash course how to solder circuits

by Clifton Mosciski 5 min read

Part of a video titled Soldering Crash Course: Basic Techniques, Tips and Advice!
4:16
16:11
Slide it into the pinholes. And then bend the legs outward to hold it into. Place. Use the tip ofMoreSlide it into the pinholes. And then bend the legs outward to hold it into. Place. Use the tip of your soldering iron to heat up both the pinhole. And the leg at the same time.

How to solder through-hole components to a circuit board?

Now place the two tinned wires together and hold still while heating them with the soldering iron so that the tin on both of the wires melt together. Next, let’s see how to solder through-hole components to a circuit board. Start by placing the component into its holes. Place it so that its legs come out on the same side as the solder pads.

How easy is it to learn soldering?

Basic soldering is easy. All you need is a soldering iron and some solder. When my dad taught me as a teenager, I remember picking it up quite fast. In this soldering guide, you’ll learn first learn to solder two wires. Then you’ll learn to solder components on a circuit board.

How to solder a PCB?

Soldering on a PCB. Bend the leads of the part so that it stays in its place. Put the tip of the iron on the pad so that it heats both the lead of the part and the pad of the circuit board. Heat them for a second or so before you apply solder. Remove the iron and the solder wire and inspect your solder joint to see if it looks okay.

How to use an iron to solder parts?

Now you’re ready to start soldering. Put the tip of the iron on the pad so that it heats both the leg of the component and the pad of the circuit board. Heat them for a second or so before you apply solder. Keep the iron on the joint while you add solder.

How do I learn to solder electronics?

1:273:41Skillbuilder: Learn to Solder - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere's no better way to learn to solder than to splice two wires. Together i have my workspaceMoreThere's no better way to learn to solder than to splice two wires. Together i have my workspace prepared by holding both ends of the wire in a tool called helping hands.

How do you solder a circuit?

1:163:51How to Solder on Circuit Boards! - YouTubeYouTubeStart of suggested clipEnd of suggested clipWith any soldering you always want to apply heat to both the pad or in this case a through-hole andMoreWith any soldering you always want to apply heat to both the pad or in this case a through-hole and the leg. And let the solder do the work and fill the through-hole. Completely again apply heat.

What are the 3 steps to proper soldering?

What are the Steps involved in the Wave Soldering Process?Step 1 – Melting the Solder. This is the very first step in the entire wave soldering process. ... Step 2 – Cleaning the Components. This is a very crucial step to be carried out. ... Step 3 – Placement of the PCB. ... Step 4 – Application of Solder. ... Step 5 – Cleaning.

What is the trick to soldering?

2:565:4610 Soldering Tips to Instantly Improve Your Soldering Skills - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust an overall more versatile tip to use tip number three pretend. All wires and pads beforeMoreJust an overall more versatile tip to use tip number three pretend. All wires and pads before soldering it'll make everything. So much easier melted solder bonds to solder instantly.

What are the four steps to soldering?

Flux – please see the page titled: Soldering 101 – Oxidation, Flux, and Firescale/stain Prevention.Step One: Good Fit. This just means that the two pieces of metal that you are joining together, fit as closely as possible. ... Step 2: Clean Metal/Solder/Flux/Hands. ... Step 3: Heat. ... Step 4: Flux.

Is it hard to solder electronics?

4:306:51How to Solder Electronics - YouTubeYouTubeStart of suggested clipEnd of suggested clipThat have been sitting on the shelf for a long time buildup oxidation layers that can make solderingMoreThat have been sitting on the shelf for a long time buildup oxidation layers that can make soldering very difficult and require more aggressive fluxes in general.

What are the six simple steps of soldering?

Just Follow the instructions given below and Watch The Video to get Perfect Soldering Results!Step 1: What You'll Need. A 20-40 Watt Soldering iron or a Mini Soldering Station. ... Step 2: Tinning. ... Step 3: Soldering Wires. ... Step 4: Soldering on PCB's. ... Step 5: Cleaning the Flux. ... Step 6: Soldering Tips!

How do you solder for beginners?

0:163:56Soldering Tutorial for Beginners: Five Easy Steps - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou'll need a soldering iron something with which to clean your tip like a wet sponge or a brassMoreYou'll need a soldering iron something with which to clean your tip like a wet sponge or a brass sponge. Some solder and while optional a pair of helping hands can really come in handy.

What are the 10 steps of soldering?

For a more thorough overview of soldering techniques, check out my other Intro to Soldering instructable.Step 1: Solder. For Simple Bots, the ideal solder is . ... Step 2: Turn It On. ... Step 3: Picking It Up. ... Step 4: Putting It Down. ... Step 5: Tin the Tip. ... Step 6: Strip Wires. ... Step 7: Twist. ... Step 8: Solder.More items...

How do you master solder?

1:097:35How to master soldering (solder tips & tricks) - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou want to solder. There is some thin tips for thin component food and larger ones for largerMoreYou want to solder. There is some thin tips for thin component food and larger ones for larger component food the second tool is the solder wire or the core wire.

Is soldering a skill?

Soldering is very much a skill and requires practice. A good joint needs to be clean and hot.

Can I solder without flux?

Yes, you need flux. Solder wire usually has flux in its core, but most still apply additional flux. I would figure out what specification of flux is in the solder wire you're using and buy that type. To obtain the best results, always use extra flux!

How is a soldering iron held?

Instead of holding it by the tip, you hold the soldering iron further back by the insulated handle .#N#That's all there is to that.

How to connect batteries in series?

The easiest way to connect batteries in series is to use a battery holder. To calculate the voltage that a battery holder provides, you simply need to count the number of batteries it holds and multiply it by 1.5V, just as you would with any other set of batteries connected in series.

What happens if a ball travels at a high speed?

If you have a small ball traveling at a very high speed, it could potentially have as much or more power as a large ball traveling at a very low speed. In this way, you could say there is a direct relationship between the speed a ball is traveling, the size of the ball, and the potential power of the ball.

How does a power supply work?

A power supply is connected to both terminals on a light source, and then electricity is allowed to flow through it, which completes the circuit and turns the light on. That is the most fundamental circuit that can be made. Of course more complex circuits can be made.

Is a circuit with a minimum amount of resistance optional?

Thanks to this law, a circuit having a minimum amount of resistance is not optional, but necessary. The energy in the circuit must encounter resistance in order to expend itself. The thing in the circuit which uses energy is considered the Load.

Can power supplies be connected in parallel?

Power supplies such as batteries can also can be connected in series and parallel. However, before we get to that, let us take a moment and talk a bit more about batteries.

How to solder through holes?

Next, let’s see how to solder through-hole components to a circuit board. Start by placing the component into its holes. Place it so that its legs come out on the same side as the solder pads. On the solder side of the board, bend the legs of the component a bit.

How to get good at soldering?

The quickest way to get good at soldering is to practice on a lot of circuits. For example, get yourself some soldering kits to practice on. Or you can find yourself some interesting circuits on your own and solder them onto a stripboard.

What to do when soldering iron is hot?

When the iron is hot, the first thing you should do is to clean the tip to remove old solder from it. You can use a wet sponge, a copper scouring pad, or something similar. Before you start soldering, you should tin the tip of the soldering iron. Which just means to melt some new solder onto the tip.

How to make a thick wire melt faster?

If it is a thick wire, you should turn up the heat on your iron ( if possible) to make the wire heat up faster. Repeat the tinning process on the other wire. Now place the two tinned wires together and hold still while heating them with the soldering iron so that the tin on both of the wires melt together.

How to join two wires with solder?

If you want to join two wires with solder, the first thing you should do is to tin the two wires. Note that the wire will get hot, so you should consider holding it with some tweezers or similar. Place the tip of the iron on the wire and let it heat for a few seconds.

Can I learn to solder?

Everyone can learn how to solder. And it’s an important skill to know want to build electronics. Basic soldering is easy. All you need is a soldering iron and some solder. When my dad taught me as a teenager, I remember picking it up quite fast. In this soldering guide, you’ll learn first learn to solder two wires.

How important is it to stay alert while soldering?

So, it is extremely important that you stay very alert while working with a soldering iron, right up to it's cooling time, and not let distractions take you away from the task at hand. This prevents you or your surroundings from coming to harm. Ask Question.

What is tinning the tip of a soldering iron?

For a new soldering iron, you will want to melt a thin coat of solder onto the tip. This is considered "tinning the tip." This thin coat will help to provide a base of solder which will help the solder to flow when you actually try to solder things later.

How to work with lead?

Working with lead requires precautionary measures such as: 1 Always wash your hands with soap and water after handling solder to wash the lead off. 2 Take common-sense precautions like not wiping your eyes, nose or mouth, to avoid absorbing lead.

Can you put soldering iron back on soldering iron stand?

Always put the soldering iron back onto the soldering iron stand when you are done using it. An unattended soldering iron that has not been properly put away can be disastrous, so it is extremely important that you always do this. We want to create, not destroy anything.

Is it easier to learn soldering?

Learning the basics of soldering is easier than you may think. Follow s is a crash course on how to solder two wires together. This is an essential skill to know when just getting started with electronics, and is a skill that is used often when making Simple Bots.

Can you pick up a soldering iron?

This cannot be stressed enough... Always pick up the soldering iron by the insulated handle! The metal part of the soldering iron is extremely hot and accidentally gripping it will result in terrible burns. It is generally thought that you should hold the soldering iron as though you were gripping a spoon.

Can you use 60/40 rosin core solder?

Feel free to try slightly thinner or thicker diameter solder, but it is highly recommended that you stick with 60/40 rosin core solder. It is fair to assume the solder contains lead, unless stated otherwise on the packaging. Working with lead requires precautionary measures such as:

What you'll learn

Students will be able to analyze and construct basic analog and digital circuits. As well as design printed circuit boards, assemble and get them running.

Requirements

A modern Windows PC (or VM) capable of running various CAD and design tools used in this course such as Altium CircuitMaker, Labcenter Proteus, Matlab, and more.

Description

Crash Course Electronics was designed for one thing -- to take you from mystery to mastery in Electronics and PCB Design. This massive course was custom made for those interested in learning electronics from the ground up that wish to leverage that knowledge to build actual printed circuit boards (PCBs).

Who this course is for

Anyone interested in learning electronics and/or printed circuit board design.

Instructor

I hold degrees in Mathematics, Computer Science and Electrical Engineering from San Jose State University. I am a Computer Scientist, Electrical and Embedded Engineer that specializes in hardware design, gaming, AI, and robotics.

image